Passive Filters Mcqs

This set of Electrical engineering Multiple Choice Questions & Answers (MCQs) focuses on study of “ Passive Filters ”. These questions are chosen from a collection of most authoritative and best reference books on Electrical engineering. Our aim is to prepare an individual for competitive exams like NTS, GAT, ECAT, University and College entrance exams, Jobs and interviews. One should practice our MCQS to assimilate Passive Filters comprehensively.

  1. Home
  2. »
  3. Engineering
  4. »
  5. Electrical Engineering Mcqs
  6. »
  7. Passive Filters Mcqs

Computer MCQS

Sciences MCQS

1.
In a certain low-pass filter, fc = 3.5 kHz.if the input voltage is a 6 V sine wave with a dc level of 10 V, what is the output voltage magnitude?

0 V

5.97 V

6 V

597 mV

Answer Discus (0)

2.
A parallel resonant band-pass filter consists of a 90 Ω resistor in series with a parallel network made up of a 60 mH coil and a 0.02 µF capacitor. The output is taken across the capacitor/coil. The coil winding has a resistance of 20 Ω. What is the center frequency of the filter?

459 Hz

4,591 Hz

999 Hz

2,176 Hz

Answer Discus (0)

3.
An RL high-pass filter consists of a 470 Ω resistor and a 600 mH coil. The output is taken across the coil. The circuit’s critical frequency is___________?

125 Hz

1,250 Hz

564 Hz

5,644 Hz

Answer Discus (0)

4.
An RC low-pass filter consists of a 120 Ω resistor and a 0.002 µF capacitor. The output is taken across the capacitor. The circuit’s critical frequency is___________?

333 kHz

633 kHz

331 kHz

60 kHz

Answer Discus (0)

5.
In a certain low-pass filter, fc = 3.5 kHz. Its pass-band is_______________?

0 Hz to 3.5 kHz

0 Hz

3.5 kHz

7 kHz

Answer Discus (0)

6.
An RC high-pass filter consists of an 820 Ω resistor. What is the value of C so that Xc is ten times less than Rat an input frequency of 12 kHz?

81 µF

161 µF

0.161 µF

220 µF

Answer Discus (0)

7.
In a series resonant band-pass filter, a lower value of Q results in______________?

A higher impedance

A smaller bandwidth

A higher resonant frequency

A larger bandwidth

Answer Discus (0)

8.
The maximum output voltage of a certain low-pass filter is 15 V. The output voltage at the critical frequency is_____________?

10.60 V

0 V

21.21 V

15 V

Answer Discus (0)

9.
The same signal in Problem 2 is applied to an RC high-pass filter. If the reactance is zero at the input frequency, the output voltage is____________?

12.73 V peak-to-peak

18 V peak-to-peak

9 V peak-to-peak

Zero

Answer Discus (0)

10.
A sinusoidal voltage with a peak-to-peak value of 18 V is applied to an RC low-pass filter. If the reactance at the input frequency is zero, the output voltage is____________?

18 V peak-to-peak

Zero

9 V peak-to-peak

12.74 V peak-to-peak

Answer Discus (0)

11.
Vout = 500 mV, and Vin = 1.3 V. The ratio Vout/ Vin expressed in dB is__________?

0 dB

8.30 dB

-8.30 dB

0.8 dB

Answer Discus (0)

12.
A parallel resonant band-pass filter consists of a 6.8 Ω resistor in series with a parallel network made up of an 8 µH coil and a 120 pF capacitor. The output is taken across the capacitor/coil. Assume RW = 0 Ω. What is the center frequency of the filter?

5.14 MHz

514 kHz

5.03 MHz

503 kHz

Answer Discus (0)

13.
In a certain low-pass filter, fc = 3.5 kHz. If the input voltage is a 6 V sine wave with a dc level of 10 V, what is the output voltage magnitude?

0 V

5.97 V

6 V

597 mV

Answer Discus (0)

14.
An RL low-pass filter consists of a 5.6 mH coil and a 3.3 kΩ resistor. The output voltage is taken across the resistor. The circuit’s critical frequency is______________?

93.8 kHz

93.8 Hz

861 Hz

86.12 kHz

Answer Discus (0)

15.
An RC high-pass filter consists of a 0.2 µF capacitor and a 220 Ω resistor. The output is taken across the resistor. The circuit’s critical frequency is_____________?

723 Hz

7,234 Hz

362 Hz

3,617 Hz

Answer Discus (0)

Engineering MCQS

General Subjects MCQS

0Shares
0
Scroll to Top